You know that maintaining the weed eater is the best way to increase its lifespan. You want to get a proper knowledge on how to clean a weed eater carburetor. You are looking for a step by step guide that explains this process in detail.
If this is the case, keep reading!
In this post, we will dive deep into how to clean a weed eater carburetor, general FAQs on weed eater carburetor and more.
Let’s get started!
Step by Step Instructions on How to Clean a Weed Eater Carburetor
Keep the Required Tools for Cleaning Nearby
The first and the most important step to do when you decide to clean the weed eater carburetor is to keep the required tools nearby. When you have everything with you while cleaning, it’ll save a lot of time.
The tools that are needed for cleaning the weed eater carburetor are very few. In fact, you only require having a flathead screwdriver. Yes, you’ve heard it right. You only need a flathead screwdriver.
Related: 10 Best Weed Eater (Commercial & gas powered string trimmers review)
Get the Necessary Repair Knowledge before You Start
This is also an important step you have to get it right before you start the actual process of cleaning the weed eater carburetor. Just like any other cleaning work, you need to have sufficient knowledge on how to do it correctly. Here’s why.
You are going to remove the carburetor from your weed eater and you’ll clean it. Once you’ve finished the job, you need to know how to put it back in place. When you don’t have this knowledge, you’ll have to pay somebody to do it for you.
If you really don’t have time, then it’s absolutely fine to get the help of a weed eater mechanic. Otherwise, you can do it yourself.
All it takes is a little bit of patience and some time for learning.
Start the Cleaning Process
Now that you’ve done the prerequisite steps, it’s time to get to the carburetor cleaning.
- In most weed eaters, there will be a bolt that holds the carburetor in place. To get to the bolt, first remove the air filter cover.
- Then, remove the air filter.
- You can see that there are two screws that hold the primer bubble of the carburetor in place.
- When you unscrew it, the carburetor splits into two.
- The main reason we opened the carburetor is to unclog it.
- First, wipe it with a dry cloth and then, wipe the insides of the carburetor with a wet cloth.
- Now, dry the carburetor and make sure that not even a small drop of water is inside.
- After ensuring that the carburetor is dried completely, put it together.
- Insert the two screws in the respective holes and fasten them.
- Ensure that the carburetor is perfectly fit into its place.
- After that, insert the air filter and the air filter cover in their appropriate areas.
- Make sure that your weed eater is put together properly.
Now that the carburetor is cleaned, your weed eater would perform at its best without any hiccups.
Conclusion
We hope that our guide on how to clean a weed eater carburetor would have provided you a basic understanding on how to go about it. Cleaning a weed eater carburetor isn’t just about removing the carburetor, wiping and putting it in place. Get a proper knowledge on how to do it before you begin.
Want to add your thoughts? Put them in the comments section below!
Related: How to Develop a Lawn Fertilizer Schedule? A Detailed Overview
FAQs about Weed Eaters
What is the Fuel-Oil Mix Ratio for a Two-Cycle Weed Eater?
The two-cycle weed eater fuel-oil mix ratio is generally 40:1. The easiest way to obtain this ratio is to mix 3.2 oz of two cycle air cooled engine oil with one gallon of regular gas. After some time, the oil will automatically separate from the gas. In order to ensure a proper oil and gas mixture, you can shake the mixture thoroughly before refueling your unit.
Why it is necessary to Use a Fuel-Oil Mixture in a Two-Cycle Weed Eater?
An important aspect to note is that all two-cycle weed eaters should use the fuel that is mixed properly with the regular gas. Unlike the other engines that have separate storage space for oil and gas, the two-cycle weed eater engine must run on a gas and an oil mixture to keep it lubricated at all times. If you use a straight gas into a two-cycle weed eater engine, it’ll destroy the engine within minutes.
